Showing posts with label clasp. Show all posts
Showing posts with label clasp. Show all posts

Clasp how-to ...

by Barbara Lewis

Kelli gave such a good tutorial on how to make an S-clasp, so I thought I would follow on her heels.  To start, cut 2.5" of 16 to 14 gauge wire.  I use 16 gauge. I don't usually hammer the ends of my wire to get a flattened look.  I narrow the ends ... it's a personal preference.  

Step 1 - You can place the wire in a ring clamp or hold it in your hand.  For the last 1/2" of wire, file to narrow it, rotating the wire as you go to keep the end symmetrical.  Repeat for the other end. 




Step 2 - Place the wire between the jaws of round nose pliers so that you just "feel" the tip of the wire protruding from between the jaws.



Step 3 - With your other hand, swing the wire around the jaw of the pliers to create a smooth loop.





Step 4 - Repeat steps 1 through 3 with the loop at the tip of the wire facing in the opposite direction as the one you just created.

Step 5 - Rest the wire on a cylinder that is approximately 10 to 12mm in diameter with the loop facing you. If you're right-handed, place your thumb on the loop to steady it.  Use your left hand to swing the wire around the pen to create a loop.




 Step 6 - Sew one end of the clasp closed with either 24 or 22 gauge wire.



Step 7 - (Not Shown)  Rest the large curve of the clasp on a bench block and hammer to strength the clasp and to create aesthetic interest. Repeat for the other end. 

Step 8 - Either leave the clasp bright and shiny or oxidize it in Black Max or other blackening solution.  Remove oxidation from the highlights with a 3M sanding pad (Fine). 



The finished product.  You may choose to add the clasp to your jewelry before the end is sewn closed or in this case, I'll be wire wrapping a bead onto the clasp, which is also a secure attachment.




Tip:  Use your crimping pliers to tuck in the ends of wire.


Ta Da!

How to make beaded clasp

As a continuation from my previous post on
How to make Egyptian Coil Bracelet (Free tutorial), I am going to show you how to make beaded clasp to complete the Egyptian coil bracelet. Of course, you can apply this to any other bracelet.


Cut 6 cm of 20ga copper wires. Make a circle of about 1.5cm in diameter using a mandrel.



Make a loop at one end of the wires.

String in some seed beads to fill up the circle.

Take the remaining side of the wires and wrap it around the folded loop.

Cut of excess wires. The loop portion of the clasp is complete.




Now take a 5cm 20ga wires. Make a loop at the middle of the wires by grasping the pliers slightly to the right of the centre with the round nose pliers.

With your left hand, guide the left side of the wires up and over the top of the round nose pliers. Continue to bring the other side of the wires up and over the top of the round nose pliers.

A loop is formed.

String in some seed beads until you fill up the wires. Leave about 0.6cm wires at the end.

Make a loop at the end of the wires.

String in seed beads at the side of the wires and make a loop at the end.

String in a jump ring onto the loop of the bar.

Now connect the bar and the bracelet by placing the jump ring onto the hook of the last link.

You are done with the beautiful Egyptian coil bracelet. Click here to download the tutorial in PDF file.



Don't miss a post! Subscribe to Handmade Jewelry Club by Email FREE

Feel free to distribute the content of the post. Just give us the credit by providing a link back to http://www.handmade-jewelry-club.com/

Find the website useful? You can easily link us using the codes below by just copy and paste them into your blog or website. You can also include the codes in your email and recommend it to your friends!Photobucket




Bookmark and Share